
Sewer Pipe Lining Rancho Palos Verdes, CA
Sewer pipe lining builds a new pipe inside the old one — a resin liner cured in place, with no joints for roots to enter and no trench across the yard.
Need help with your sewer line?
Call Now to reach a local sewer professional. Describe the problem, where it is, and what the line has been doing.
Hours: Mon–Fri 7:00 AM–10:00 PM PT · Sat 8:00 AM–10:00 PM PT · Sun 7:00 AM–9:00 PM PT
What this service does
Sewer pipe lining, known as cured-in-place pipe or CIPP, renews a damaged sewer line from the inside. A liner soaked in resin is inserted into the old pipe and cured with hot water or steam, hardening into a smooth, jointless pipe within the old one. The old pipe stays in the ground and becomes a shell around the new liner. There is no trench, no removed pipe, and no digging along the line — the work happens through small access points at each end. The liner is also the answer for a line that leaks. A cracked clay tile line does not only let roots in; it lets wastewater out, and the water escaping from the line can wash soil away from around the pipe, which lets the pipe settle further. A liner seals the cracks from the inside, so the leaking stops and the soil around the pipe stays where it is. The line stops damaging the ground it sits in.
Lining is the answer for a particular kind of failure, and Rancho Palos Verdes has a lot of it. The city's laterals are mostly clay tile, cast iron, or bituminous fiber from the 1950s through the 1970s, and they fail at the joints: roots enter, joints separate, cracks open, and scale builds up inside cast iron. A liner seals all of those joints at once, because the finished pipe has no joints at all. A root cannot enter a pipe that has no seams, and wastewater cannot leak out through a crack that is covered from the inside. The joints are the reason lining works so well on clay tile. A clay lateral has a joint every two or three feet, and each joint is a place where roots can enter and wastewater can leak. A liner covers them all at once, because the finished pipe has no joints at all. The crew does not have to find and seal each joint one by one; the liner seals the whole run in a single installation.
A lined pipe is built to last. CIPP liners are designed to a fifty-year design life, which puts lining in the same category as a new pipe rather than a patch. The liner is slightly smaller in diameter than the old pipe, because it sits inside it, but its smooth interior often flows as well as the rough, scaled interior of the old pipe. Lining does not suit every line — a collapsed pipe, a bad belly, or a sharp offset needs a different answer — but for a line that still holds its shape, it is the least disruptive way to give the home a new pipe. The fifty-year design life is the standard the liner is built to, and it is what separates lining from a patch. A patch covers a crack; a liner is a new pipe with its own structural strength, designed to carry the load of the soil above it and the flow of the home it serves. The old pipe around it becomes a shell, and the liner does the work. The camera check at the end confirms the liner is continuous from the house to the street main.
Before you call
- Stop using water if the line is backing up.
- Keep people and pets away from any wastewater.
- Note which drains are slow, and which one backs up first.
- Note whether the problem happens in heavy rain, or all the time.
- Have the age of the home ready, if you know it.
How CIPP lining works, step by step
The job starts with a camera inspection and a measurement. The camera shows the pipe material, the damage, and whether the line still holds its shape — a liner needs a roughly round, continuous pipe to form inside. The crew measures the length and the diameter of the run, and the liner is cut to that length. A line that has collapsed flat, or one with a sharp sideways offset where two sections have shifted apart, cannot be lined, and the camera is what finds that out before the liner is ordered. The measurement also decides the thickness of the liner. A deeper line, or a line under a driveway, needs a thicker liner than a shallow line under a lawn, because the liner has to carry the load of the soil and the traffic above it. The crew chooses the liner from the depth and the location the camera recorded, not from a standard size.
The liner itself is a flexible tube, usually felt or fiberglass, soaked in a resin that hardens when heated. The crew inverts the liner into the old pipe with air or water pressure — turning it inside out as it goes in, so the resin-coated side presses against the old pipe wall — or pulls it into place with a cable. Once the liner is in position, hot water or steam is circulated through it, and the resin cures into a hard, smooth pipe. The curing takes time, and the line cannot be used while it happens. The resin is the part of the job that needs care. It has to be mixed and soaked evenly through the liner, so the cured pipe is the same thickness along its whole length. A liner that is thin in one section is weak in that section, and the camera check at the end is what shows whether the liner cured evenly. The curing temperature and time are monitored through the whole cycle.
When the resin has cured, the ends of the liner are trimmed, the connections at the house and at the street main are reinstated, and the finished line is camera-checked. The camera shows a smooth, continuous pipe with no joints, no cracks, and no roots. The liner has sealed every joint and crack it covered, and the old pipe around it is now a shell rather than the working pipe. The access points are closed, and the yard above the line was never opened. The connections are reinstated with a cutting tool that opens the liner where the branch lines join the main run, the connections from the house fixtures that meet the lateral along its length. Each opening is cut cleanly so the branch drains into the lined pipe without catching on the edge of the liner. The camera confirms each connection is open and clear before the job is called done.

What the service includes
Camera inspection and measurement
The line is camera-inspected and measured end to end, so the crew knows the length, the diameter, and whether the pipe still holds its shape well enough to take a liner.
Cleaning before lining
The line is jetted clean before the liner goes in, so the liner bonds to the pipe wall rather than to grease, scale, or root cuttings. A liner installed over buildup does not seat properly.
Resin liner installation
The liner is soaked in resin and inverted or pulled into the old pipe, pressing against the pipe wall along the full length of the run, from the house to the street main.
Hot-water or steam curing
Hot water or steam circulates through the liner until the resin hardens into a smooth, jointless pipe inside the old one. The curing is monitored so the liner hardens evenly along the run.
Connections reinstated
The connections at the house and at the street main are reinstated and sealed after curing, so the lined pipe carries wastewater from the home all the way to the main.
Final camera check
The finished line is camera-checked end to end, confirming the liner is continuous, smooth, and clear, with no wrinkles, no gaps, and the correct fall toward the street main.
How the work runs
Describe the symptoms
Slow drains, repeat backups, roots at the joints, or a camera report that shows a cracked or leaking line. Whether the pipe still holds its shape is the question that decides if lining fits.
Camera inspection
The camera maps the line from the house to the street main: material, joints, damage, and shape. A collapsed section or a sharp offset means lining is not the answer.
Cleaning the line
The line is hydro jetted so the liner meets a clean pipe wall. Grease, scale, and root cuttings are flushed out before the liner goes in.
Liner installation
The resin-soaked liner is inverted or pulled into the old pipe and positioned along the full run, pressing against the pipe wall from end to end.
Curing
Hot water or steam circulates through the liner until the resin hardens into a new pipe. The line is not used while the curing is under way.
Reinstate and final check
The connections are reinstated, the liner ends are trimmed, and the finished line is camera-checked before the access points are closed.
Tools and methods used
Sewer camera with locator
The camera shows whether the pipe holds its shape well enough to take a liner, and the locator marks the line's path and depth on the surface.
Hydro jetter
The jetter cleans the line before lining, so the liner bonds to the pipe wall rather than to buildup. A clean pipe is what makes a liner seat properly.
CIPP inversion equipment
The liner is inverted into the old pipe with air or water pressure, then cured with hot water or steam until the resin hardens into a new pipe.
Curing monitor
Temperature and pressure are monitored through the curing cycle, so the resin hardens evenly along the full length of the run.
Sewer pipe lining cost: what decides it
Sewer pipe lining has no single per-foot figure, because the figure follows the line itself. The length of the run is the first driver, and the diameter is the second: a longer line takes a longer liner, and a larger line takes more resin. The number of connections matters too, because each branch that joins the line has to be reopened after the liner cures, and a line with many branches takes more work than a straight run. Bends and offsets add care, and access at both ends decides how the liner goes in. The curing method — hot water or steam — is chosen for the line, and the line cannot be used while the resin hardens, so the curing window is planned with the household before the liner goes in.
The comparison most homeowners ask about is lining vs replacement, and the two suit different lines. Lining, sometimes called a sleeve, forms a new jointless pipe inside the old one, and it suits a line that still holds its shape, because the liner needs a sound shell to form against. Replacement takes the old pipe out and lays a new one, and it suits a line that has collapsed, or one that is undersized for the home it serves. The pros and cons of lining are straightforward. The pros are that it needs only small access points, leaves the yard in place, and gives the line a fifty-year design life with no joints for roots to enter. The cons are that it cannot correct a belly or a separated joint, because the liner takes the shape of the old pipe, and it makes the bore slightly smaller, even though the smooth interior usually flows as well as the rougher pipe it replaces.
A clay tile line leaking at every joint
A lateral that keeps backing up will not heal — the water keeps coming back through the lowest drain in the house.
A smooth, jointless pipe inside the old one
The work is checked with a camera, not a look at the surface — the new line is seen end to end before the job is called done.
Problems pipe lining solves
- Roots entering through the joints of a clay tile lateral.
- Cracks and leaking joints along a line that still holds its shape.
- Scale and roughness inside old cast iron that slows the flow.
- Repeat backups from a line whose joints keep opening.
- A lateral under a driveway or patio that cannot be trenched.
- Wastewater leaking out of the line through cracks and open joints.
Signs pipe lining may fit your sewer line
- A camera inspection shows cracks or leaking joints, but the pipe still holds its shape.
- Roots have entered at many joints along the run, and cleaning only buys a few months.
- The line is clay tile from the 1960s or 1970s, with joints that keep opening.
- The lateral runs under a driveway, a patio, or mature trees you want to keep.
- You want the joints sealed without a trench across the yard.
- The pipe is corroded or scaled inside, but not collapsed.
- The line is long, and replacing it by trench would disturb a large area.
- A previous camera report shows the line is round and continuous, with damage at the joints.
Related services
Trenchless Sewer Repair · Pipe Bursting · Sewer Line Replacement
Industries that use this service
Hillside & Slope Properties · HOA & Multi-Family · All industries →
Related guides
Old Pipes in Rancho Palos Verdes · RPV Sewer Permits · All guides →
Frequently asked questions
Questions people ask about sewer pipe lining, answered plainly.
Sewer pipe lining, or CIPP, builds a new pipe inside the old one. A liner soaked in resin is inserted into the existing pipe and cured with hot water or steam, hardening into a smooth, jointless pipe. The old pipe stays in the ground as a shell around the new liner. There is no trench, and the yard above the line is never opened. The old pipe stays in the ground and becomes a shell around the new liner, so there is no pipe to remove and no trench to dig. The yard above the line is never opened, and the access points at each end are closed when the work is done.
The line is camera-inspected and measured, then jetted clean so the liner meets a clean pipe wall. The resin-soaked liner is inverted or pulled into the old pipe and positioned along the full run. Hot water or steam is then circulated through the liner until the resin hardens into a new pipe. The connections at the house and the street main are reinstated, and the finished line is camera-checked.
CIPP liners are designed to a fifty-year design life, which puts lining in the same category as a new pipe rather than a patch. The finished liner has no joints for roots to enter and a smooth interior that resists buildup. How long it lasts in practice depends on the condition of the old pipe around it and on the ground it sits in, but the design life is the standard the liner is built to. The design life assumes the liner was installed on a clean pipe wall and cured evenly, which is why the cleaning before lining and the monitoring during curing matter. A liner installed over buildup, or cured unevenly, will not reach its design life, and the camera check at the end is what confirms the installation was sound.
Yes, slightly. The liner sits inside the old pipe, so the inside diameter is a little smaller than it was. In practice, the smooth interior of the liner often flows as well as the rough, scaled interior of the old pipe, and the crew checks the diameter and the fall before recommending lining over bursting. A line that is already undersized for the home may be a better candidate for bursting.
It depends on the belly. A mild belly can sometimes be lined, but a liner follows the shape of the old pipe — it does not correct the fall. A deep belly is a low spot where water and solids sit, and the liner will have the same low spot. A bad belly usually needs the section dug and re-graded, which means a trench for that part of the run. A liner follows the shape of the old pipe, so a deep belly will still hold water after the lining is done. The camera shows the belly before the work is planned, and the crew explains whether the section needs to be dug and re-graded instead. Lining a bad belly is a job that looks done on camera and fails the next time the line is used heavily.
Lining builds a new pipe inside the old one, so the finished diameter is slightly smaller and the old pipe remains as a shell. Bursting breaks the old pipe outward and pulls a completely new pipe into the same path, so the finished pipe can be the same size or larger. Lining fits a line that still holds its shape; bursting fits a line that is badly damaged or undersized.
Yes — clay tile is one of the strongest cases for lining. Clay tile fails at its joints, and a liner seals every joint at once, because the finished pipe has no joints at all. The camera inspection has to show the pipe still holds its shape; a clay line that has collapsed flat, or one with a sharp sideways offset, cannot be lined. Clay tile is also the material where lining saves the most digging, because a clay lateral has a joint every two or three feet and each joint is a potential leak. Lining seals them all in one installation, where a spot repair would have to find and fix each joint one at a time.
A lined pipe can be camera-inspected like any other pipe, and it can be jetted to clear buildup. If a section of a lined pipe is damaged later, the repair depends on where the damage is and how the liner was installed — the camera shows the condition, and the crew explains the options for that section. The camera footage from the lining job is the record of what was installed. A lined pipe is also a pipe that can be lined again in the future if a new problem appears, though the options depend on the condition of the liner and the old pipe around it. The camera is the tool that shows the condition, and the crew explains the options from what it finds.
There is no fixed per-foot figure, because the work follows the line: its length, its diameter, how many branch connections have to be reopened after curing, how many bends it has, and how the liner is accessed at each end. A short, straight run with few connections is the simplest case. A long run with many branches takes more work, and the camera inspection gives the measurements the plan is built from.
Sewer line trouble in your Rancho Palos Verdes home?
Call Now to reach a local sewer professional. Describe the problem, where it is, and what the line has been doing.
Call now for sewer line help
Tap Call Now to reach a local sewer professional. Tell them where the problem is, what the line has been doing, and whether wastewater is coming into the home.
Hours: Mon–Fri 7:00 AM–10:00 PM PT · Sat 8:00 AM–10:00 PM PT · Sun 7:00 AM–9:00 PM PT
Before you call
- Stop using water if the line is backing up.
- Keep people and pets away from any wastewater.
- Note which drains are slow, and which one backs up first.
- Note whether the problem happens in heavy rain, or all the time.
- Have the age of the home ready, if you know it.








